4 Roll plate bending
UHSS-4 Plate Bending Machines are very suitable for medium and heavy plates or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on this machines. Our UHSS-4 models are also ideal machines for wind towers production, Shipyard and Pipeline Industries.
|
UHSS-4 Line
|
|
- Pinch roll and lateral rolls move pyramidal linear with hydraulic pistons
- Overload Protection
- Top Roll and Lateral Rolls are powered by hydromotor and planetary gearbox (3 roll driven system)
- Three digital readouts for easy roll positioing
- Hydraulic tiltable Drop-End for easy removal of finished ferrule
|
|
- Easy operation with mobile control panel
- Welded steel frames
- Induction hardened forged SAE 1050 (CK 50) Steel rolls
- Conical bending device
- Central lubrication system
- Hydraulic balancing system (Ø460 and below)
- Electronic balancing system (Ø500 and over)
- Double speed working system
|
UHS-4 Plate Bending Machines are very suitable for medium and light plates or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on this machines.
|
UHS-4 Line
|
|
- Pinch roll and lateral rolls move with hydraulic pistons in orbital way
- Overload protection
- Top Roll powered by hydromotor and planetary
gearbox ( Only top roll powered )
- Three digital readouts for easy roll positioning
- Hydraulic Drop-End for easy removal of finished ferrule
|
|
- Easy operation with mobile control panel
- Welded steel frames
- Induction hardened forged or rolled SAE 1050 (CK 50) Steel rolls
- Conical Bending device
- Hydraulic balancing system
- Double speed working system
|
UHMS-4 Plate Bending Machines are very suitable for light and medium plates, aluminum or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on this machines. Our UHMS-4 type machines are top and bottom roll powered models.
|
UHMS-4 Line
|
|
- Pinch roll and lateral rolls move with pyramid linear direct movement by hydraulic pistons.
- Overload protection
- Top roll is powered by electrical motor and planetary gearbox. Bottom roll powered with cardan joint system (two rolls powered )
- Three digital readouts for easy roll positioning
|
|
- Hydraulic Drop-End for easy removal of finished ferrule
- Easy operation with mobile control panel
- Welded steel frames
- Induction hardened forged or rolled SAE 1050 (CK 45) Steel rolls
- Conical bending device
- Hydraulic balancing system
|
URH-4 Plate Bending Machines are very suitable for light plates, aluminum or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on this machines. The URH-4 machines are Cassette type special system designed models for elliptic or round shapes in mass production as low as 20 sec. cycle time.
|
URH-4 Line
|
|
- Roll and lateral rolls move with hydraulic piston through casette type frame
- Overload protection
- Top roll is powered by planetary gearbox. Bottom and side rolls free
- Easy operation with mobile control panel
- Welded steel frames
|
|
|
URM-4 Plate Bending Machines are very suitable for light plates, aluminum or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on this machines. Our URM-4 type machines are the most economical four roll plate bending machines.
|
URM-4 Line
|
|
- Pinch roll and lateral rolls move with screw jacks in linear way
- Overload protection
- Top roll is powered by planetary gearbox. Bottom and side rolls free
- Easy operation with mobile control panel
- Welded steel frames
- Conical bending device
|
|
|
3 Roll plate bending
UHSS-3 Plate Bending Machines are very suitable for medium and heavy plates or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on these machines.
|
UHSS-3 Line
|
|
- Lateral rolls move linear way with hydraulic pistons
- Overload protection
- Lateral rolls and top roll is powered by hydromotor and planetary gearbox (3 rolls driven)
- Hydraulic Drop-End for easy removal of finished ferrule
- Easy operation with mobile control panel
- Two digital readouts for easy roll positioning of bottom rolls
|
|
- Welded steel frames
- Induction hardened forged or rolled SAE 1050 (CK 45) steel rolls
- Conical bending device with ball bearing
- Central lubrication system
- Hydraulic balancing system
- Electronic balancing system (Ø 500 - 550)
- Double speed working system
- Extended roll shafts for profile and pipe bending operation
|
UHS-3 Plate Bending Machines are very suitable for medium and light plates or stainless steel bending. Ferrules in full circle or varying radiuses can be done easily on these machines.
|
UHS-3 Line
|
|
- Lateral rolls move with hydraulic pistons in orbital way
- Overload protection
- All rolls are powered by hydromotor and planetary gearbox
- Hydraulic Drop-End for easy removal of finished ferrule
- Easy operation with mobile control panel
- Welded steel frames
|
|
- Two digital readouts for easy roll positioning of bottom rolls
- Induction hardened, hot rolled SAE 1050 (CK 45) steel rolls
- Conical bending device with ball bearing
- Hydraulic balancing system
- Extended roll shafts for profile and pipe bending operation
|
|
UHST-3 Line
|
|
- The solid construction and the particular geometry of the UHST-3 enable to be used as a press brake bending machine
- The posibility to reduce centre-distance between lower rolls realizes a better pre-bending during bending of tubes with small diameter and thickness
- Another important feature of the UHST-3 machine is the operating system of the top forming roll. In fact, the top forming roll can be used as a traditional press brake allowing perfect rerolling and calibration operations of the produced tubes
- In the same way it is also possible to obtain cones with heavy thickness by bending in several strokes the plate
- With some 3 and 4 rolls pyramidal machines it is necessary to tilt the top roll to allow the produced tube removal. On the UHST-3 machine this is not necessary and therefore it is much more easier to remove the finished tube
- The UHST-3 machine can fulfill the best pre-bending on every required diameter.
|
|
- Large working stroke allows to get best bending result
- Can bend more thicker plates compare to equivalent 3 or 4 roll machines
- Induction hardened forged or rolled SAE 1050 (CK 45) Steel Rolls
- Double Speed Working system
- Conical Bending device
- Electronic balancing system
- High efficiency on heavy plate bending operation
- Reduced overall dimensions and easiness of transportation on medium and big machines
- During operation (pre-bending and bending phases), the plate always keeps its horizontal position. So material moves more easily.
- Having the two bottom rolls horizontally moving, means also a lower working height which requires a smaller foundation pit and less anchoring load (in the smallest models you don’t need foundation)
|
This hydraulic model is designed for light to medium jobs. It is used in jobs up to 10 mm thickness materials. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Machine Sheet Metal Cover Parts.
|
URM-H Line
|
|
- Steel welded main frames
- Hydraulic Drop-End
- Mobile control panel
- Motor powered central rolls
- Hydraulic movement of back roll and bottom roll
- Main motor with brake system
- Conical bending, Pre-Bending available
|
|
- Support system for top roll
- Planetary Gearbox two rolls driven
- Back roll with ball bearings for thin sheet works
- SAE 1050 (CK45) certificated forged steel rolls with high tensile strength
- Hardened rolls
- 2 pcs. digital Read-Outs
|
This mechanical model is designed for light to medium jobs.It is used in jobs up to 8 mm thickness materials. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Machine Sheet Metal Cover Parts.
|
URM-S Line
|
|
- Two rolls powered by a single chain and belt driven Helical type Gearbox and gear system
- SAE 1050 (CK 45) Quality Certificated steel rolls with high tensile strength
- Steel welded main frames
- Mechanical manual openable Drop-End
- Mobile control panel
- Conical bending device
- Central lubrication system
- Top roll support system
- Precision bending with brake motor
- Motorised adjustment of back roll
|
|
|
This mechanical model is designed for light to medium jobs. It is used in jobs up to 5 mm thickness materials. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Sheet Metal Covers. Its ideal price makes it very attractive for small workshops.
|
URM Line
|
|
- Two rolls powered by a single gearbox and gear system for top and bottom rolls.
- SAE 1050 Quality certificated steel rolls with high tensile strength.
- Spheroid cast iron main frames.
- Mobile control panel by foot pedal.
- Conical Bending Device.
- Manual Drop-End.
- Top roll support system.
- Wire grooves at the end of the rolls
- Precision bending with brake motor
|
|
|
This mechanical model is designed for light to medium jobs. It is used in jobs up to 3 mm thickness materials. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Sheet Metal Covers. Its ideal price makes it very attractive for small workshops.
|
UM Line
|
|
- Top and bottom rolls powered by a single gearbox and gear system
- SAE 1050 Quality Certificated steel rolls with high tensile strength
- Cast iron main frames
- Mobile control panel by foot pedal
- Conical bending device
- Manual Drop-End
- Wire grooves at the end of the rolls
- Precision bending with brake motor
|
This mechanical model is designed for light to medium jobs. It is used in jobs up to 3 mm thickness materials. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Sheet Metal Covers. Its ideal price makes it very attractive for small workshops.
|
US Line
|
|
- SAE 1050 Quality Certificated steel rolls with high tensile strength
- Cast iron main frames
- Conical bending device
- Manual Drop-End
- Wire grooves at the end of the rolls
|
This mechanical model is designed for light to medium jobs. It is used in jobs up to 2 mm thickness materials. Hand powered or motorised models are available. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Sheet Metal Covers. Its ideal price makes it very attractive for small workshops.
|
UR Line
|
|
- Top and bottom rolls powered by a single Gearbox and gear system
- SAE 1050 Quality Certificated steel rolls with high tensile strength
- Cast iron main frames
- Mobile control panel by foot pedal
- Conical bending device
- Manual Drop-End
- Wire grooves at the end of the rolls
- Precision bending with brake motor
|
This mechanical model is designed for light to medium jobs. It is used in jobs up to 2 mm thickness materials. Hand powered or motorised models are available. It is used in Aluminium Bendings, Air Conditioning Channels, Advertising Panels and Sheet Metal Covers. Its ideal price makes it very attractive for small workshops.
|
U Line
|
|
- SAE 1050 Quality Certificated steel rolls with high tensile strength
- Cast iron main frames
- Conical bending device
- Manual Drop-End
- Wire grooves at the end of the rolls
|
